J. Perry & Sons frames and finishes curved drywall for homes, condos and commercial spaces in Broward and Palm Beach counties: radius walls around a stair or foyer, arched doorways and niches, barrel-vault hallways, curved soffits over a kitchen island or reception desk, and the groin and dome ceilings that show up in Mediterranean-style houses from Boca Raton to Wellington. This is a specialty within our stucco and drywall finishing work. A curve is only as good as its framing and its finish, so the same crew lays out the radius, bends the board and skims it to Level 5. We also do the reverse: removing dated arches and squaring them.
Curved Drywall Cost in South Florida: $45–$90 per linear ft of wall
| Scope | Typical size | Installed range |
|---|---|---|
| Curved wall, framed and finished, 8–10 ft tall | per linear ft of curve | $45–$90 per lf |
| Arched doorway or cased opening in drywall, new or converted from square | 3–4 ft wide | $600–$1,400 each |
| Arched niche with curved back, finished | 2x4 ft | $700–$1,500 each |
| Barrel-vault ceiling over a hallway | 4 ft wide x 12–20 ft long | $3,500–$8,000 |
| Curved soffit or bulkhead over island or desk | per linear ft | $60–$120 per lf |
| Radius or dome ceiling in a foyer or dining room | 10–14 ft diameter | $6,000–$15,000 |
| Square off an existing drywall arch (interior only) | per opening | $450–$900 each |
Pricing covers layout, metal or wood framing, flexible or double-layer 1/4-inch board, bead, tape, a Level 5 skim and sanding. Tighter radii cost more because the board has to be wetted, scored or doubled, and soffit and ceiling work adds lift and overhead time. Lighting, electrical and paint are separate.
Free Estimate
Free estimate — call (561) 556-7509 or email jperrysonsgc@gmail.com with project photos, the city, approximate dimensions, and material selections.
Curves we build and how each is framed
Radius walls. Laid out from a center point on the floor, framed with flexible track kerfed on 2-inch centers for the curve, studs at 8 inches on center or closer. Board is 1/4-inch flexible gypsum in two layers for radii under 8 feet, or 1/2-inch board scored and wetted for gentle curves.
Arched openings. Framed with a plywood or pre-formed arch kit set in the opening, blocked to the header, and faced with flexible board or flexible arch bead. The soffit of the arch gets a strip of 1/4-inch board bent to the curve. Elliptical and segmental arches are laid out full scale on the floor first. See the curved wall cost guide.
Barrel vaults. Radius ribs cut from plywood or formed from bent track, spaced 12–16 inches, with 1/4-inch flexible board bent across them in two layers. The transition to flat ceiling is run with flexible bead.
Dome and groin ceilings. Built on a frame of radial ribs; board is cut in gores or replaced with a fiberglass-reinforced plaster form where the double curve is too tight for gypsum. Finished in setting compound and skimmed.
Curved soffits and bulkheads. The island and reception-desk soffit: a curved frame hung from the ceiling joists or deck, boarded on the face and bottom, with a light cove or LED channel built in if wanted.
Squaring an arch. The arch frame comes out, the opening is reframed square, boarded and finished. Most 1990s houses here have three to six of them.
Free estimate — call (561) 556-7509 or email jperrysonsgc@gmail.com. Send a photo of the space and the shape you want and we'll return a range the same day.
How we build a curved wall or ceiling
- Layout. The radius is drawn full scale on the floor or on a template from a center point. For ceilings, ribs are cut to the template before anything goes up.
- Framing. Kerfed flexible track top and bottom, studs on 6–8 inch centers for tight radii. Ribs for vaults and domes are set to a laser line.
- Board. Flexible 1/4-inch gypsum is applied in two layers, joints staggered, screwed on 6-inch centers. For gentle curves, 1/2-inch board is scored on the back or wetted and set over a few hours.
- Bead. Flexible vinyl or paper-faced flex bead on every curved edge and arch soffit so the line stays true.
- Tape and finish. Setting compound in the first coat on all joints to control shrinkage over the layered board, then two more coats.
- Level 5 skim. Every curve is skimmed in full. Curves catch light from every angle and show board joints that a flat wall hides.
- Sand under raking light. A work light set low along the curve finds every flat spot and ridge before the painter arrives.
Curved drywall in South Florida: block walls, humidity and condos
Furring and block. Curved walls inside a CBS house are usually freestanding partitions, which is simple. A curve against a block wall needs a furred cavity and the depth to fit it.
Humidity. Wetted board and setting compound both dry slowly in summer. We allow extra time between layers so the second layer is not screwed to a damp first layer that will shrink.
Condos. Curved soffits and bulkheads in condos often hide sprinkler mains and HVAC, and the association wants to see the layout and the permit. We coordinate both and work within building hours.
Mediterranean houses. Boca Raton, Parkland and Wellington have a generation of homes with arches, niches and groin vaults built by production crews. Repairs, matching an existing arch, and squaring them off are a regular call.
Permits. Non-structural interior partitions and ceilings usually fall under a renovation permit; stand-alone cosmetic work generally needs none. We advise per municipality.
Related stucco and drywall services
- Drywall finishing Levels 3, 4 and 5: the finish standard every curve gets.
- Drop ceilings, soffits and ceiling details: trays, coffers and lighting coves.
- Window and door opening reshaping: arches to squares on the exterior side.
- Plaster repair and Venetian plaster: decorative finish over a curved wall.
- Stone veneer: clad a radius wall or arch in stone.
What a curved drywall estimate includes
- Radius, height and linear footage of each curve, or the arch dimensions
- Framing method: kerfed track, ribs, arch kit
- Board layers and type
- Flexible bead footage
- Level 5 skim on all curved surfaces
- Lift or scaffold for ceilings
- Electrical rough-in coordination for coves and LED channels
- Paint, if included
Curved walls and arches by city
Stucco & drywall in Fort Lauderdale · Stucco & drywall in Miami · Stucco & drywall in Boca Raton · Stucco & drywall in West Palm Beach · Stucco & drywall in Weston · Stucco & drywall in Delray Beach · Stucco & drywall in Parkland · Stucco & drywall in Wellington
Planning guides: Curved drywall walls and ceilings · Drywall Level 5 finish explained · Drop ceiling vs tray ceiling · Cost to square an arched window opening · Interior painting cost guide
Curved walls, arches and radius ceilings — FAQ
How much does a curved drywall wall cost? $45–$90 per linear foot of curve for an 8–10 foot wall, framed, boarded in two layers and skimmed to Level 5. Tight radii and ceilings sit at the top of the range.
Can you make a square doorway into an arch? Yes. An arch kit or plywood form goes into the existing opening, the soffit is boarded with flexible gypsum and finished, at $600–$1,400 per opening.
Can you remove the arches in my house? Yes. Interior drywall arches are squared at $450–$900 each. Arched exterior windows are a different scope and are covered under opening reshaping.
Why does the curve need Level 5? A curve picks up light from every direction, so every board joint and screw dimple shows. A full skim gives one continuous surface.
How do I get an exact price? Call (561) 556-7509 or email jperrysonsgc@gmail.com with photos and rough dimensions. A written estimate is typically ready within 24–48 hours after a site review and scope confirmation.
Free estimate — call (561) 556-7509 or email jperrysonsgc@gmail.com. Licensed Florida general contractor CGC1540699. Serving Broward and Palm Beach counties.
Permits and compliance handled. J. Perry & Sons pulls the permit, schedules the inspections, and builds to the city and county codes that apply — Broward and Palm Beach municipal building departments, HVHZ requirements where they apply, and HOA/condo association rules. Licensed Florida general contractor CGC1540699.
Free Estimate
Free estimate — call (561) 556-7509 or email jperrysonsgc@gmail.com with project photos, the city, approximate dimensions, and material selections.